KUNJUNGI WEB SAYA

Urutan Warna Kabel UTP Cara Mudah

Beberapa hari yang lalu, saya diminta temen masang kabel UTP di sebuah SEkolah Menengah Pertama (SMP).

Sebenarnya bukan masalah warnanya, Tetapi masalah impedansi antar kabel yang di tata sesuai warnanya harus 100 Ohm. Mau warna apa saja tidak ada masalah asalkan urutan warna pasangannya harus pas. untuk searah contohnya (putih orange & orange) harus terus berpasangan demikian juga yg lain. pasangan pin 1&2 pasangan pin 3&6. karena tiap pasangan warna mempunyai impedansi 100 Ohm. Coba deh tukar warna lain asal pasangannya tepat pasti konek. Untuk pin 4,5,7,8 hanya digunakan untuk POE saja. Tapi ada yang lebih rinci di bawah ini :

Kronologisnya begini :
SMP tersebut berencana untuk mensharing koneksi internetnya yang berasal dari speedy ke semua client di gedung sekolah tersebut. Tahap awal, dipasang untuk 4 (empat) client dengan panjang kabel masing-masing dari HUB yaitu 2 meter, 8 meter, 20 meter dan 70 meter.

Seperti biasa, sesuai ilmu yang saya tau (entah dari mana ilmu tersebut), bahwa untuk koneksi PC ke HUB dibutuhkan kabel straight, dan (lagi-lagi) berdasakan ilmu yang saya dapat tersebut, saya langsung memasang konektor RJ-45 di kedua ujung kabel tanpa memperhatikan urutan warna, yang penting kedua ujung sama urutan warnanya.
Saat memasang kabel yang 2 meter dan 8 meter, tidak ada masalah dalam pengetesan (ping replay). Giliran kabel yang 20 meter dan 70 meter, hasil tes selalu RTO (Request Time Out), wah apa yang salah nih.

Prediksi awal kesalahan saya timpakan pada konektor atau crimping yang kurang kuat, potong dan bikin dengan konektor baru lagi, hasilnya tetep RTO.

Berikutnya kesalahan saya timpakan pada kabel UTP, pasti ada yang putus nih, setelah dites dengan MULTI TESTER ternyata semua ujung kabel tersambung dengan baik.

Kesalahan ketiga saya jatuhkan pada kabel yang terlalu panjang (lho?? iya, saya ngotot ke temen saya kalo kabelnya kepanjangan, 20 meter dan 70 meter itu terlalu panjang menurut saya). Namun setelah mencoba googling berapa sih panjang maksimal untuk kabel UTP saya jadi bingung sendiri, di forum-forum disebutkan bahwa rata-rata panjang maksimalnya adalah 100 meter (nah lho, bingung ndiri).

Akhirnya Allah memberi petunjuk, lewat forum-forum itu pula saya melihat urutan warna untuk kabel UTP, baik untuk sambungan Straight maupun Cross. Akhirnya dengan harap-harap cemas (malu sama temen yang minta tolong) saya ikuti urutan warna yang disebutkan di forum tersebut untuk kabel Straight. Hasilnya...Alhamdulillah kabel 20 meter bisa reply, begitu juga untuk kabel ang 70 meter.

Sebenarnya saya sudah tau sejak jaman kuliah kalo ada standard urutan warna untuk kabel UTP, namun karena dalam prakteknya setiap kabel yang saya sambung selalu berhasil connect maka saya tidak begitu percaya dengan teori warna tersebut.

Berikut adalah urutan warna yang saya dapat saat menjelajah forum networking, barangkali berguna buat yang lain.




Dari pengalaman diatas saya punya kesimpulan bahwa kalau memasang konektor RJ-45 tanpa memperhatikan urutan warna, maka koneksi yang didapat tidak akan maksimal, sehingga ketika dipasang pada kabel yang lebih dari 10 meter (mungkin lho) koneksi akan lost.
Di Wikipedia juga ada yang lebih rinci penjelasannya, lanjutkan click yang di bawah... :
  1. Wiki UTP Languange English
  2. Category 5 Cable UTP languange English
  3. Cara Mudah memasang UTP "Twisted Pair"
Kalo Ini Salah Tolong beri komentar ....

Man Of The Match Piala Dunia 2010

Man Of The Match Piala Dunia 2010
masih Diego Forlan man of the match sekarang...
Apakah penghargaan Man of Match?
Untuk pertama kalinya dalam sejarah Piala Dunia FIFA ™, Man of the Match untuk pertandingan masing-masing akan dipilih oleh Anda, para penggemar!
Ini berarti Anda memutuskan pemain terbaik dan siapa yang dapat menerima Man Budweiser dari piala Match ketika permainan berakhir.
Dimana saya bisa memilih untuk Man of the Match?
Kami adalah memudahkan Anda untuk memilih.
Jika Anda mengikuti Piala Dunia FIFA pada fitur MatchCast Emirates di FIFA.com, Anda akan dapat memilih dalam MatchCast pada setiap pertandingan tunggal!
Atau Anda dapat membuat penunjuk, www.fifa.com / pria untuk memastikan Anda dapat menempatkan suara Anda dengan hanya beberapa klik mouse.
Bagaimana cara kerja suara?
Yang harus Anda Anda adalah memilih pemain Anda merasa pantas untuk memenangkan penghargaan Man of Match.
Voting terbuka selama setiap pertandingan dari Piala Dunia 2010 FIFA segera setelah babak kedua dimulai. Anda dapat memilih, dan bahkan mengubah suara Anda, sampai pertandingan berakhir.
Kapan itu mulai?
Anda dapat memulai pemungutan suara selama Pembukaan Match dari Piala Dunia 2010 FIFA. Pertandingan akan dimulai pada 11 Juni, 16:00 CET. Voting akan terbuka pada awal semester kedua setiap pertandingan.
Pastikan untuk mengunjungi FIFA.com pada tanggal 11 Juni, dan setiap matchday, ke tempat suara Anda!

CommentLuv Now available for blogger platform

Platform
users it’s time that you can say Hurray! because popular wordpress plugin CommentLuv which I am using it in my blog to share luv with my commentators is now also available for Blogger users.
This actually got released a week ago but I didn’t blogged about it at that time as the site(www.js-kit.com) was having some problems with their servers while installation
. But now everything is good and I have tested it on my blogspot test blog.

It is actually a part of JS-kit Intense Debate commenting system which can be installed very simply. During installation
it will back up all your existing comments and will keep a copy of all comments in sync with your blog so you can stop using it any time. It even allows you to take your comments with you when you move blogs. This commenting system allows your readers to comment with many choices plus they can also add their pictures while commenting.
You can get more info about it on the official blog post.
You can also check this system running on my test blog post.
So have you started using it? What’s your feedback on it?

Mikrotik premium free download new relase 2010

Mikrotik premium free download new relase 2010

       Howto change CPU frequency on RB532A 04.05.09

Here’s a quick video showing how to change CPU frequency on RouterBOARD 532A from 266MHz to 400MHz in BIOS during the boot sequence.
CLICK RouterOS 3.x release with the longest lifetime in 2008 
During the year 2008 a total of 18 RouterOS 3 versions were released, from 3.0 to 3.17. So which one had the longest lifetime, which was the most stable release? Read on to find out.

CLICK RouterBOARD 433UAH announced 

New router board was just announced, and it’s  featuring two USB ports! Basically it’s an expanded version of the well-known RouterBOARD 433AH.

CLICK MikroTik RouterOS 3.23 released 

Lots of improvements and bufixes in the new RouterOS 3.23:
*) fixed installation on fresh disks or VMs;
*) add 802.1ad Service Tag support for VLAN;
*) wireless - fix for RTS/CTS when used together with dynamic ACK timeout;
*) serial ports are now grouped per USB device;
*) added gsm info command to ppp-client;
*) added URL support to fetch tool;
*) added dial-on-demand mode to PPTP & L2TP clients;
*) ssh - now non-interactive console commands can reference variables;
*) fixed TFTP server logging;
*) fixed problem - “/system upgrade” (autoupgrade) did not show proper package
architecture and was unable to fetch new packages;
*) fixed bug - hotspot ‘walled garden ip’ rules did not work on some boards
after reboot;
*) added ‘/interface print stats’ command;
*) improved support for OSPF as PE-CE routing protocol;
*) added OSPF sham links;
*) fixed a bug in set-bgp-prepend-path routing filter;
*) fixed some MPLS TE reoptimize bugs;
*) added MPLS TE bandwidth management features;
*) netwatch - ignore items with interval 0s, this value was causing
netwatch to fail;
*) routing-test - added new type of gateway argument: ip address together with interface;
*) api - ‘disabled’ property was not available from api since 3.21, fixed;
*) api - added support for retrieving OID values;
*) api - removed special behaviour of ‘find’ command under API. Use
‘print’ command with queries instead of ‘find’. This change fixes
scripts that are started from API and contain ‘find’ command.
*) console - removed support for octal numbers, now string of digits with
a leading zero is interpreted as decimal number;
*) console - added binary ~ operator that matches value against
POSIX extended regular expression;
*) console now accepts decimal numbers with k/K M G T P suffixes for
values of some properties;
*) console - fixed export problems:
if long line is wrapped just before space charater, the space character
has to be escaped, otherwise it is lost;
errors during export generated a comment line that was incorrectly enclosed
in quotes;
*) console - added binary ~ operator that matches value against
POSIX extended regular expression;
*) scheduler - added owner and policy properties; all existing
scheduler entries will get owner name “*sched” and policy
read,write,test;
*) routing-test - allow to specify that route gateway is in the main routing table;
*) added route cache statistics;
*) fixed mesh protocol;
*) graphing - fixed IP address mask display issue for low endian architectures;

CLICK MikroTik RouterOS 4.0 beta2 released 

RouterOS 4.0 beta2 just came out, here’s what’s new:
*) console: added ‘without-paging’ argument to ‘monitor’ commands;
*) console: now ‘without-paging’ and ‘interval’ arguments in of ‘print’
commands work together. Printing can be stopped by pressing ‘q’ or
ctrl-c, any other key triggers printing;
*) incorporated all the bugfixes since v3.22;

CLICK MikroTik Certified Integratetor (MCI) 

MikroTik company,  Mikrotīkls Ltd, just announced a new program for approved companies who build systems for RouterOS or make accessories for MikroTik products. Program is named MCI - MikroTik Certified Integrators, and the certified products will be recognisable by the “Powered by MikroTik” stickers.

CLICK MikroTik RouterOS 3.22 released 

RouterOS version 3.22 was released today with some new features:
*) added advanced switch features for RB450G;
*) added support for MetaROUTER on RB450G;
*) added support for adding physical interfaces to Metarouters;
*) added set-bgp-prepend-path action to routing filters;
*) added WinBox OSPFv3 support to routing-test package;
*) added WinBox IPv6 routes support to routing-test package;
*) console - added ‘hide-sensitive’ option to the export command;
*) user manager - fixed customer remove interface bug;
*) fixed Cisco BGP VPLS autodiscovery in mpls-test package;
*) fixed LDP to not disconnect on unknown capabilities of remote
peer (should help establish LDP session with Junos);
*) fixed ethernet port name reordering on RB493;
*) bonding mode balance-alb now works on RB1xx, RB4xx, RB616, RB600, RB750,
RB1000;
*) added ‘/interface ethernet print stats’ command for RB450G and RB750;
*) fixed CSPF in routing-test to properly interpret link bandwidth;
*) added support for C-motech CNU-680 CDMA 1x EV-DO 450Mhz USB Modem;

CLICK RouterBOARD 1000 encryption engine boosted with RouterOS 3.20 

RouterBOARD 1000 comes with an onboard encryption engine, however RouterOS releases before version 3.20 couldn’t use it’s full potential. Now the 3.20 software puts the encryption hardware into full use thus providing a fantastic 11 times speedup with 3DES encryption and 6,5 times speedup when using AES128 encryption!
MikroTik  testing results state the following:
v3.19
AES128: 79Mbps
3DES: 45Mbps
v3.20
AES128: 510Mbps
3DES: 500Mbps

CLICK MikroTik RouterOS 3.21 released 

Version 3.21 brings a lot of fixes and few improvements:
*) backported MetaROUTER support for RB4xx from v4;
*) added WinBox MPLS & VPLS support mpls-test package;
*) added WinBox BGP support to routing-test package;
*) api - added query support for ‘print’ command;
*) added support for bsd-syslog;
*) added TFTP server;
*) added authorization and TLS support to email tool;
*) added pppoe-scanner;
*) added tftp protocol support to fetch tool;
*) fixed ipsec policy priority to work as documented;
*) fixed BGP route selection in routing package;
*) allow to use IPsec aggressive mode with pre-shared keys;
*) fixed some problems in mesh protocol;
*) fixed https proxying with parent proxy;
*) fixed Prism shared IRQ issue;
*) fixed multiple MPLS/VPLS bugs in mpls-test;
*) fixed boot problems on some RB1000s;
*) added /interface mesh traceroute command;
*) fixed web proxy source address selection;
*) fixed pcq queue - pcq sometimes could get through more traffic
than specified in max-limit;

CLICK RouterBOARD 450G announced 

New MikroTik RouterBOARD 450G was announced, featuring five Gigabit ethernet ports, 256MB RAM, microSD card slot and powerful  Atheros AR7161 680MHz CPU. 

Software pembagi bandwidth untuk Warnet

Software pembagi bandwidth untuk Warnet

1. OVERVIEW!

  • Berikut ini adalah topologi dari jaringan yang akan saya bangun
  • net_diagram1
  • Saya menggunakan Windows XP sebagai server dan ICS sebagai sarana untuk membagi koneksi internet
  • Untuk modem saya menggunakan HUAWEI K3520 (yang sebenarnya tidak layak untuk dijadikan server :P )
  • Broadband akses saya menggunakan Broom upto 256 kbps
  • Pada server saya menginstall SoftPerfect Bandwidth Manager (BDM) sebagai software untuk me-manage bandwidth, kenapa? karena menurut saya software ini paling mudah untuk dipahami
Berapa kecepatan bandwidth saya?
Menurut pengalaman saya + kata dosen saya :) cukup melihat kecepatan yang diberikan oleh provider (contoh Broom upto 256kbps) lalu bagikan dengan 8 karena 1Byte=1/8 bit berarti kalau 1KB = 1024bit ok kita coba itung koneksi Broom, inget loh ada tulisan “Up To” nya kalau di bahasa indonesiakan kurang lebih “sampai dengan” lah jadi ga terus2an di 256Kbps tergantung banyak faktor yang mempengaruhi
Broom= 256Kbps = 256/8 KBps = 32KBps nah perasaan tuh di kaliin lagi sama 8/9 tapi lupa lagi ngga tau angka 8/9 ini dari mana munculnya ahahahak! jadi 32KBps * 8/9 = 28,444444444 KBps
Jadi saya mempunyai kecepatan koneksi sebesar 28,4444444 KBps (di bulatkan brapa yah?)
2. GOAL!!
  • Memanage bandwidth sesuai kebutuhan, contoh untuk komp A kita kasih bandwidth 5KBps karena mungkin komp A hanya digunakan untuk browsing, komp B 10KBps karena sering digunakan untuk mendownload, dan komp C 5KBpsnet_diagram2
  • Mengontrol Quota (bagi yang menggunakan broadband tipe volume based)
  • Menjaga agar server tidak overflow (untuk pc rumahan) gara-gara request bandwidth yang berlebihan
3. ATTENTION!!
  • Bila dilihat dari figure di atas semua  koneksi internet yang dilakukan oleh client (komp A,B,C) harus melalui komputer server terlebih dahulu, yang harus diperhatikan adalah interface-nya yaitu Network Card / LAN Card (bukan modem)
  • Dalam menggunakan BDM ada 4 hal yang harus diperhatikan yaitu Bandwidth (banyaknya bandwidth yang akan diberikan kepada sebuah komp), Source (dari mana paket data berasal), Destination (hendak ke mana paket data menuju), dan Interface (melalui apa paket data dikirimkan), 4 hal tersebut disebut “Rules” atau aturan main
  • “Rules” untuk jaringan yang akan saya bangun adalah sebagai berikutnet_diagram3
  • BDM memiliki feature untuk mengontrol pemakaian quota, gunakan feature ini untuk menghemat pemakain quota anda
4. ACTION!!
4.1 Men-seting  SoftPerfect Bandwidth Manager (BDM) Rules pada komp server

  • Saya asumsikan jaringan ICS telah terkoneksi dengan baik dan lancar, untuk mengetahui bagaimana membangun jaringan dengan model ICS silahkan liat di….om google :P
  • Install SoftPerfect Bandwidth Manager (BDM) di komputer server, lalu jalankan nanti akan muncul login prompt, langsung tekan “OK” saja karena secara default service BDM tidak menggunakan password
    live_bandwidth3
    note: apabila anda mengalami kegagalan ketika proses login coba restart ulang terlebih dahulu komputer anda, apabila masih tidak bisa login coba cek apakah service BDM sudah berjalan atau belum, silahkan pergi ke Control Panel –> Administrative Tools –> Services
    services_di_cpanel
    coba scroll ke bawah pastikan service BDM status-nya “started”
    services_di_cpanel2
    Kalau tidak klik 2 kali pada list lalu tekan “Start”
    services_di_cpanel3
  • Setelah berhasil login klik menu Rules –> Add Rule
  • bandwidth_manage1
  • Masukan “Rules” yang akan kita buat, dalam contoh kali ini silahkan lihat kembali setingan “Rules” di atasBerikut adalah gambar penerapan Rules pada Software BDM bdm_rules1
    bdm_rules2
    bdm_rules3
    Setingan di atas adalah setingan untuk komp A, sedangkan untuk Komp B dan C, caranya sama saja, hanya ada sedikit perubahan yaitu pada bagian “Single IP Address”, rubah menjadi IP Address milik Komp B (192.168.0.3) lalu lanjutkan dengan IP Address Komp C (192.168.0.4).
    Apabila telah selesai men-seting seluruh komputer client (komp A, B, C) maka hasilnya akan terlihat seperti di bawah ini
    bdm_rules4

    note: anda dapat menambah Rules sesuai dengan kebutuhan
  • Selesai :)
  • Untuk pengecekan silahkan masuk ke menu Tools –> Live Bandwidth Monitor, di situ anda dapat melihat grafik pemakaian bandwidth oleh tiap-tiap komputermenu_live_bandwidth
    live_bandwidth1
4.2 Mengontrol Quota Dengan SoftPerfect Bandwidth Manager
  • Sebagai pengguna akses internet broadband berbasiskan volume based terkadang kita suka memiliki pikiran seperti ini “Bagaimana yah caranya supaya quota 3Giga bisa mencukupi pemakaian internet selama 1 bulan??, sehingga tidak terjadi over quota yang tentu saja bikin kantong terkuras :)
  • Nah dengan menggunakan SoftPerfect Bandwidth Manager (BDM) ini anda dapat mengontrol quota dengan sangat mudah
  • Contoh saya menggunakan koneksi internet Broom yang memiliki quota 3Giga itu berarti kalau di hitung-hitung3Giga / 30 hari = 100MB, berarti dalam satu hari, pemakaian quota maksimal adalah 100MB Apabila quota telah mencapai titik maksimal-nya (100MB) maka koneksi internet akan otomatis terputus, dan saya harus menunggu keesokan harinya untuk mendapatkan quota 100MB lagi (kembali terkoneksi dengan internet)
  • Sekarang saya akan mencontohkan bagaimana men-seting BDM agar dapat mengontrol pemakaian quota kita.Silahkan balik lagi ke BDM-nya klik di menu Tools –> Quota Manager , lalu klik tombol New , setelah itu masukan setingan untuk quota-nya, contoh 100 MB per hari (lihat gambar) BDM_quota_manager1
    BDM_quota_manager2
    BDM_quota_manager3

    • Untuk “Initial Rate” anda dapat memasukan value sesuai kebutuhan, “Initial Rate” adalah bandwidth yang disediakan apabila quota per hari (100MB) masih ada atau valid
    • Sedangkan “Reduced Rate” adalah bandwidth yang disediakan apabila quota per hari (100MB) telah habis, dalam contoh diperlihatkan saya memilih “Blocked” yang artinya apabila pemakaian quota per hari (100MB) telah habis maka otomatis koneksi internet akan terputus
    Setelah berhasil klik tombol OK, nanti hasilnya akan terlihat seperti ini
    BDM_quota_manager4
  • Terakhir jangan lupa untuk menambahkan Rules pada BDM, isi Rules dengan maksimal quota per hari (100MB/HARI) yang baru saja di buatklik menu Rules –> Add Rule , lalu masukin setingan-nya seperti di bawah ini bandwidth_100mb_perhari
    bandwidth_100mb_perhari2
    bandwidth_100mb_perhari3
  • Selesai :)
  • Untuk mengecek berapa banyak quota yang telah terpakai, silahkan lihat pada bagian “Quota Used”bandwidth_100mb_perhari4
  • Coba test, maksimalkan pemakaian quota 100MB/hari sampai habis (quota used = 100%), maka semua komputer (Komp A, B, C, dan SERVER) akan terputus dari internet secara otomatis, dan anda serta teman2 anda yang sedang asyik ber-facebook ria harus menunggu hingga esok hari untuk bisa kembali online, jadi hemat2 lah menggunakan quota :)
dan terakhir…… jangan lupa….
motto kita
Enjoyy…. :)

Hydronitrogen Blog

Hydronitrogen Blog
An awesome angry techblog about cool stuff and miscellaneity.

Slackware 13.0 and 13.1 Multilib Quick and Easy Script

I’ve been wanting to set up multilib on my 64bit Slackware box for a while but I kept hesitating because I would look at the instructions on alien’s slackbook wiki and it would look far too complicated for me. Finally I took up the daunting task only to realize it was much easier than I thought. So, for this tutorial, you need two things, a working Slackware 13.0 or 13.1 system (I’m on stable, I don’t know if it will work on current. Possibly) and an internet connection. All the URL’s I’m going to use will be for a 13.1 system, if you’re on 13.0 just change the URL’s to fit.

First download all the packages from alien’s repository.
wget -r -l1 --no-parent http://connie.slackware.com/~alien/multilib/13.1/

cd connie.slackware.com/~alien/multilib/13.1/

sudo upgradepkg --reinstall --install-new *.t?z
This sets up your system as “multilib enabled.” Next you need to download, and install the compat32 packages that allow 32 bit applications to run on your system. Doing this on 13.0 and 13.1 is different. On 13, you download the packages like so and then install them:
wget -r --no-parent http://connie.slackware.com/~alien/multilib/13.0/slackware64-compat32/

cd connie.slackware.com/~alien/multilib/13.0/slackware64-compat32/

sudo installpkg *-compat32/*.t?z
On 13.1 massconvert.sh does all the work for you.
sudo massconvert32.sh -u ftp://slackware.oregonstate.edu/pub/slackware/slackware-13.0/slackware

sudo installpkg *-compat32/*.t?z
And that’s all there is to it! Now your system is 32 bit compatible! 32 bit applications should run out of the box, and if you want to compile one just run:
. /etc/profile.d/32dev.sh
Note the dot before. BUT, if you’re building a SlackBuild though please read this note from alien’s wiki.